Site Loader

Introduction:Microprocessors do not have inbuilt memory. 8086 microprocessor was designed and invented by Intel in 1976. It’s a 16-bit Microprocessor which has 20-bit address lines and 16 bit data lines which are multiplexed (AD0-AD15). The words will be stored in two consecutive memory locations. If the first byte of the word is at an odd address, the 8086 will read the first byte in one operation and the second byte in another. Else if the first byte of word is at even address, the 8086 can read the entire word in an operation.Features:It has faster processing as it has an instruction queue capable of storing six instruction bytes from the memory.Faster processing is due to 16 bit ALU, 16 bit registers, internal data bus, and 16 bit external data bus. It was the first 16 bit processor with such features.Performance is improved by pipelining. Pipelining has two stages, i.e. Fetch Stage and Execute Stage. Fetch stage stores up to 6 bytes of instructions in queue, while execute stage executes them.It has large number of transistors, approximately 29,000 transistors.Architecture of 8086:8086 microprocessor is divided into two functional units-Execution Unit (EU) Bus Interface Unit (BIU).Execution Unit (EU)-This unit commands BIU starting from where to fetch the data and then decode and execute those instructions through giving instruction. By using instruction decoder and ALU, it controls operations on data.Some functional part of 8086 microprocessor are:ALU- It handles arithmetic and logical operations.Flag Register- 16-bit register which changes it status according to the result stored in the accumulator. There are in total 9 flags. They are divided into 2 groups – Condition Flags and Control Flags.Status Flags- It represents the result of the last instruction executed.Carry Flag (CF): This will indicate the final carry of the result given by the instruction.Auxiliary Flag (AF): This will represent the in between carries generated by the instruction executed.Parity Flag (PF): It will show the whether number of 1’s is odd or even in the result.Zero Flag (ZF): If the result of the operation is zero, then the flag will be set to 1 else 0.Sign Flag (SF): When the result of the operation is negative, then the flag is set to 1 else set to 0.Overflow Flag (OF): This will indicate the result when the capacity of the system is exceeded.Control Flags- It controls the operation of the EU.Trap Flag (TF): For debugging, it allows the user to execute one instruction at a time and is used for single step control.Interrupt Flag (IF): It allows/prohibits interruption of a program. To enable the interruption, it is set to 1 else set to 0 for interrupt disabled.Direction Flag (DF): If is used for the string operation. If the pointer is pointed at the last character of the string, then the flag is set to 1 and the pointer will be decremented. If the pointer is pointing to the first character of the string, then the flag is set to 0 and will be incremented.General Purpose Registers- There are 8 general purpose registers, namely, AH, AL, BH, BL, CH, CL, DH, and DL. These can be used individually to store 8-bit data and can be stored as 16-bit by making pairs. It is referred to the AX, BX, CX, and DX respectively.Accumulator register (AX) – Used to store operand for arithmetic operations.Base register (BX) – Used to store the starting bas address of the memory area.Counter (CX) – Used in loop instruction to store the loop counter.Data register (DX) – Used to hold I/O port address for I/O instruction.Stack Pointer Register- It holds the address from the start of the segment to the memory location.Bus Interface Unit (BIU):It takes care of all the data and addresses transferred on the buses for the EU, EU has no direct connection with System Buses so it is possible with the BIU. Both the units are connected with the internal buses. BIU has following functional parts-Instruction queue- Up to 6 bytes of next instruction is given to BIU which stores them in the instruction queue. When EU is ready to fetch the next instruction, it simply reads it from the instruction queue resulting in execution speed. Fetching the next instruction before the current execution is completed is called as Pipelining.Segment register- Bus Interface Unit has 4 segment buses, i.e. CS, DS, SS, and ES.Code Segment (CS) – It addresses the memory location in the code segment of the memory.Data Segment (DS) – Consist of data used by the program and is accessed in the DS by an offset address.Stack Segment (SS) – Handles memory to store data and addresses.Extra Segment (ES) – It is additional data segment used by the string to hold the extra destination data.Instruction Pointer- This pointer holds the address of the next instruction to be executed.

Post Author: admin

x

Hi!
I'm Matt!

Would you like to get a custom essay? How about receiving a customized one?

Check it out